x
x
Vacuum Instruments Corporation
phone
MENU

Air Leak Testing

The most advanced air leak testing capabilities and application experience in the industry.

Vacuum Instruments Corporation designs and manufactures standard portable leak detectors, mass flow systems, pressure decay systems, differential pressure decay systems, fixtures, test fittings, calibrated leaks, and accessories.

  • Fast leak and flow restriction test instruments
  • Turnkey leak-test systems
  • Mass flow meters, pressure decay, vacuum decay systems
  • Dimensional, electrical and pneumatic test systems
  • Ongoing application support
Custom Leak Test Solutions
Medical Industry Solutions
Custom solutions for medical product leak testing equipment. Methods of leak detection used by medical device manufacturers are evolving to meet increasingly stringent quality standards. Testing for leak integrity is critical in the device industry because product failure presents significant hazards to patients and healthcare professionals and liabilities for manufacturers.
Model No. Medical Industry Solutions
Automotive Fuel Delivery Solutions
Solutions for automotive fuel delivery leak testing equipment. Leak testing requirements for fuel system components have been lenient (0-2 cc/sec). Amendments to the EPA Clean Air Act and the California Air Resources Board have imposed evaporative vehicle emission standards resulting in a more stringent leak test requirement. To fulfill these test requirements, VIC has developed ultra-sensitive mass spectrometer methods to leak test fuel system components, including fuel tanks, tube and flange and fuel rail assemblies.
Model No. Automotive Fuel Delivery Solutions
Gas Handling Systems
Ready
To Go
Smart Charge III
A fully automatic, custom configurable evacuation and gas backfill system with built-in gross leak test that may be used to pre-charge products under test with gas for leak detection or for any gas charging application that requires evacuation and subsequent pressurization of a test product.
Model No. Smart Charge III, Part No. 926-326
GM-BS
A microprocessor-based system designed to blend two gas components, typically helium and air.  These systems provide a cost effective alternative to 100% tracer gas.
Model No. GM-BS, Part No. 925-090
GB-AS
Gas booster systems produce high-pressure process gas supplies from lower pressure sources, typically boosting a shop air source. Base units provide up to 600 psig pressure output. Options include higher pressure outputs and process gas drying capabilities. Can be configured for single gas or dual gas boosting.
Model No. GB-AS
HRS
Introducing a solution to lower the cost associated with tracer gas consumption While industries strive to meet increasing demands to offer higher quality products at lower prices, the need to efficiently recycle process gas becomes apparent. Helium Recovery features a group of high efficiency gas recycling systems that significantly reduce tracer operating costs. The Helium Recovery Systems offered consists of ASME coded pressure tanks, a set of compressor(s), gas analyzer, microprocessor controls and all necessary valving, gas regulation and piping.
Model No. HRS
Air Leak Detectors
Ready
To Go
VIC-Torr
The VIC-Torr is a high resolution test instrument that can be configured as a mass flow, pressure decay or vacuum decay leak tester and is available in single or multi-channel models.
Model No. VIC-Torr, Part No. 90396
MLC
The MLC Leak/Occlusion Tester for Multi-Lumen Catheters. Incorporate a process validation plan into your medical device production with V.I.C.’s MLC Leak/Occlusion Tester.
Model No. MLC
Calibrated Gas Leaks
Ready
To Go
OM
The OM Series gas calibrator leaks utilize a precision tapered glass capillary as the leak element. Gases pass through a single orifice, with the leak rate dependent upon size and gas pressure. To prevent clogging of the fine orifice, a unique particle trap is located between the capillary tube and outlet fitting.
Model No. OM
Ready
To Go
PM
The PM Series – Helium based – Gas Permeation Leak Calibrators utilize a durable 7740 Pyrex glass permeation leak element which permits diffusion of helium gas.
Model No. PM
Ready
To Go
SC
Designed for MS-40, MS-50, and MS-60 leak detectors and helium leak detectors formerly made by Veeco Instruments.
Model No. SC
Ready
To Go
E-MOTT
Ideal for calibrating VIC’s TurboTest™ MD-290S, MD-390S, MD-490S and halogen sniffing instruments. These leaks are specifically designed for atmospheric sniffing applications.
Model No. E-MOTT
Vacuum Instruments Corporation is a pioneer in providing state-of-the-art leak detection solutions for diverse applications and industries. Our systems have ensured the safety and performance of countless products that we use in our daily lives from the cars we drive to the air conditioners in our houses, the pacemakers in our bodies, and the satellites we launch into space.
LinkedIn
Vacuum Instruments Corporation, LLC
2101 Ninth Avenue, Ronkonkoma, NY 11779 USA
OFFICES   |   CONTACT US
Vacuum Instruments Corporation
2101 Ninth Avenue 11779 Ronkonkoma, NY
1-888-819-9970
1-631-737-0949
sales@vicleakdetection.com
1-888-819--9970
Legal    |    Site Map
© 2018 Vacuum Instruments Corporation, LLC.
   Back
Next
Reload